293 replies [Last post]
Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

Here is picture of RMC 3.5" cases with variety of slugs,
locked on wad slugs and sabots. There are 3 of our long cases
in back for comparison. The RMC turned cases have shotgun
primer. Case # 4 has 437gr slug in BPI SABOT( finally hard sabots
in 12ga for reloading), #5 437gr Brenekke KO slug, #6 540gr
Hammerhead slug, #7 600gr Dixie hard slug, #8 RG's 715gr
jacketed, #9 750gr solid brass. Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

Here is picture of a 12ga hard discarding sabot you can get
for reloading, the BPI. From Ballistic products. In picture
is sabot with a 437gr Hornady Great Plains 50cal slug I put
in it. Also the 410 gr and 385gr Great Plains work.
Finally able to load your own instead of paying 3-5 bucks
each for loaded rounds.You can use the 500 S&W bullets also
as well as shorter 50 cal blackpowder slugs... Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

Been testing the Encore with the Nef loads. Barrel breech is
one inch same as muzzle, where the NEF is 1.200".
It has dovetails cut out in bottom of the barrel for
the nuts for the forearm screws. ... At the bottom of dove tail
there is only .060" thickness. Before reaming had back one fill
welded as it was where the taper for the forcing cone ended up
with 3.5" chamber. I load it with 10 gr less powder than the NEF
on all different slugs and weights. Like the BPI sabot in 3.5"
plastic in NEF, 437 gr slug, 120gr 4227, 2400 fps, and in Encore
110gr 4227, 2270 fps. In 3.5" RMC brass case, same sabot/slug
in NEF 140gr 4227, 2600+ fps,Encore 130gr 4227, 2500.
The Encore is now 12 lbs, with hollow in butt and recesses in
forearm with lead shot.In pic you see NEF And Encore with RMC
brass cases started in chambers. Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

See what's possible, original Savage 210 action/stock
the one I have our long case in. You can lengthen
magazine in the plastic stock for up to 3.5" RMC brass
cases, also 3.5" plastic cases. And you can open up
bottom of the action to match, and the other things
I did on the port, bolt travel, etc to feed cases.
I did mine with heavy wood stock in singleshot.
Using original plastic stock you weight the hollow butt.
Trigger assembly on these is back to leave space for this.
In picture you see stock original and stock mag longer.
Second picture is a 3.5" brass case and slug overall
length 3.7", in longer magazine. Brett in MN, who did this
first used the regular follower and mag spring ok,
it feeds ok for him. .. Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

Info to help loading BPI sabots in plastic,ok to use plastic
overwad over powder, but should use cardboard card and
nitro wads above that below the BPI sabot. Sabot doesn't
tear up and accuracy much better. Personally I use
cards over powder and nitro wads, And with used cases
roll crimping onto the thin edge of sabot is uneven, so with
my used cases I set the sabot and slug to right height and
just redo the 6 point star crimp real hard, and the middle of
all the crimp sectors set right on the flat nose of the slug
in the sabot. I also do the same with RG's 715gr hollowpoint
with the crimp sectors right on the hollowpoint in used cases.
Roll crimping holds RG's slug in ok but its taper of the ogive and
smoothness it doesn't open crimp all the way around when
fired. The star crimp set slug at same height so you can get
the same amount of powder. With RMC brass these are not
problems but with brass to get good feeding from mag rounding
front edge of mouth helps. Sectioned picture of RMC on right
next to our long original case to show how well it is built
thick and strong. One of cases has 20 firings, still good..Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

What others are doing hopping up loads and experimenting.
Brett in MN uses a Mossy 835 12ga smoothbore turkey gun, but
it is backbored 10ga size all the way out to end and has 10ga size
choke, and he uses 12ga AQ 441gr slug with locked on basewad, from
BPI. Using top rib bead sight only he can hit a pail 5 times in a row at
70 yds.Amazing accuracy for overbored barrel. He uses BPI X12X seal
plastic wad, two 1/4" white felt wads, thin card then the AQ slug,
with 65gr of Longshot getting 2200 fps. 3.5" new cases with
roll crimp.......I asked him check it with a scope on it sometime.

NFG from Greybeard and Shotgunworld with pump Mossy and 18.5"
with slug barrel. He gets a 525gr Lyman over 1800 fps with
80gr of 4759/4227 powder. Hard alloy mix Lyman and shot one through
17" of pine. Shown in the pic below it mushroomed to .800" and only
lost 8gr weight. It is a wasp waisted slug that is shot from a 12ga
regular WW12 shotcup. The skirt of the slug collapsed into the underside
of the nose. Many guys say that these are as accurate as most
other stuff used. He used 3" plastic, PGS wad over powder and
WW12 wadcup with slug it. He cuts wadcup petals back to length
of the Lyman.In pic on left you see the Lymans with hollowbase up
and the shape of it when starting out.

Ok I am going to get Lymans to test and Longshot to test.
Got to see if the Longshot will get further up in velocity
than Blue Dot. Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

Here is a Savage 210 with bottom of action opened up
toward the back, to take cases with 3.5" overall length.
Slug Warrior on Shotgun World did it. Is similiar job the
Brett in MN did, but he made his opening 3.7". I measured
mine and they can be opened to 3.95". They also milled
the rim guides back for controlling case feeding on longer
cases. Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

Here is information and reason for keeping and milling
the rim guides back for controlling case feeding on longer
cases.Rim guides are angled in from the sides of the opening
toward back. As the bolt pushes top case in the mag forward the
back of case and rim comes to where the tapers widen out so
the case then slides up in front of the bolt.I'm fixing up my
2nd Savage I have set up for my second 700H 3.25" belted case.
Just to see how it will work and along with other guys
doing it, get the info out to people.
This work on the stock/action can be done in a vertical
mill or good drill press. To use 3.5" plastic the opening on
the action and magazine needs 3.25", for 2.875"" brass long loaded
3.5", if 3.5" brass about 3.7", if 3.5" brass long loaded, 3.95".
By long loaded I mean a slug like the Dixie 600gr that protrudes
up to .4".The 730 gr flat wide nose slug protrudes 1/8".
You also have to widen and smooth the ramp going into the
front bridge so case lifts smoothly on the way into chamber.Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

We get asked about putting brakes on the NEF Ultra.
There is the concept called the internal brake that works
nearly as good as expansion brake, with less back noise.
Rob on AR did a couple with bunch of holes in the barrel
in the end with the last 1.5" bored out .025" where holes
go. Also many want more velocity in NEf and I added on
a barrel section to mine. Combining Ideas we add smooth
9" section of bore extension, that is same as groove diameter
and 1.5" end of that for internal brake. Eight 1/8" holes
top and same 45 degees to each side.And we have over
a 100 fps in velocity gain. And with card or wad behind load
it will seal pressure going from rifled section to smooth.
And these types of holes won't bother wads or sabots.
My extension is a foot longer and gets 150 fps extra.
No need for brake in mine as the gun is 17 lbs with extra bbl.
Here is Rob's two he fixed up, and is shooting.He has
them reamed out longer for long 3.85" case, weight added.Ed

Offline
Location: Brinton, MI
Joined: 10/17/2007
Posts: 294
700HE & 12GA FH Capable---

Here is a picture of porting holes in a 10ga NEF
heavy long smooth barrel. Bbl 30" and 1.080" muzzle
diameter behind the screw in choke area. This come
with slightly extended screw in choke and is first
10ga with long barrel as heavy as my NEF 12ga FH
short barrel was.. OR the short NEF 10 gauges
with heavy barrel..It came with full and mod chokes.
The other 10ga I tested earlier, only .960" at muzzle.
I cut choke off and put it back in leaving the barrel
an open bore for slugs and leaving an area 1.2" long
for an internal brake to drill all the holes in like
Rob did with NEFs in his picture. Now the 1.2" long
area where holes are is bigger than needed for 10 ga
so a reamer in the making will solve that and solve a
major big bore project for me and others who asked
me about using the short NEF 10ga for upgrade, which
I didn't encourage putting all that work on a short
barrel gun, with the amounts of powder that will be
burnt in....are you ready.......THE 8GA FH.......
I have 8ga FH loads tested in reworked Enfield.....Ed

Related Forum Threads You Might Like

ThreadThread StarterRepliesLast Updated
What did you harvest in 2009 ???HOGGETTER501/23/2010 15:53 pm
Hunting SuggestionsAlphaMan408/08/2005 10:46 am
WTB: Browning 12ga. A-Bolt slug gunwishfish108/23/2008 19:06 pm
Remington 870 Wingmaster 12ga. PumpBronx1301/09/2004 17:51 pm
Winchester PDX 1 12ga for pigs???Alpine_Archer602/09/2011 12:38 pm